How To Jack Up Pool Legs

Download Article

Download Article

A puddle table must be level for the assurance to curlicue evenly across the felt. An uneven pool tabular array will preclude accurateness in players' shots, and will allow the balls to roll to one side or expanse of the table. With a few items from a home improvement or hardware store, such as a carpenter's tool and some shims, you tin level your pool table. Employ these tips to level a pool table.

1. 1

   Apply a carpenter'southward level. If you lot've noticed your billiard balls making strange curves, measure out your puddle table for level. The all-time way to do this is with a basic carpenter's level. Analog or digital levels both work fine.

   • Analog carpenter levels ordinarily have bubbles that will orient between 2 lines when the surface is level, and will skew to one side when the surface is crooked. These are great for telling not only whether or not your tabular array is crooked, but by how much, and to what management. ^[ane]
   • If you don't have one, at that place are free or very cheap apps you tin go on most smart phones with quite accurate level-functions. Use ane of these instead, and just lay your phone on the surface yous desire to check for level.

2. two

   Measure the mid-line of the pool table. Set the carpenter'southward level in the eye of the pool tabular array, oriented long-means. If the pool tabular array is balanced from end to end, the bubbles in the carpenter's level will be situated betwixt the two lines in the middle of the glass tubes.^[2]

   • If the bubbles in the glass tubes are in a higher place or below the middle lines, you will need to raise or lower one of the shorter ends of the pool table.

   Advertisement

3. 3

   Measure out the shorter mid-line of the pool tabular array. Plow the level the opposite direction in the middle as well, perpendicular to the long sides of the rectangle and even with the shorter sides. This will assist you measure the side-to-side level of the table.

   • Take a measurement. If the bubbling are above or below, yous'll also demand to conform the legs in that management to make the table flat.^[3]

4. 4

   Prepare the carpenter's level on each of the sides of the pool tabular array. Virtually of the time, the problem with pool tables is that 1 leg, or multiple legs, is lower than the other three legs on the tabular array. To find it, put the level close to the edge of each of the 4 sides of the pool tabular array to get a more accurate reading.

   • Move to each side and each corner of the pool tabular array, checking with the level for the severity of the lean. The corner with the most lean is the one you're looking for.
   • In some cases, you'll get weird readings because the flooring of the house may be less than level. If that's the case, you can however make adjustments in the aforementioned basic way, it'll just have a little more troubleshooting to go information technology right.

5. 5

   Use a ball to check for practical balance. Coil the cue ball over a section of the tabular array, as straight as possible. Move your eye even with the plane of the table, to look along the path of the ball. See whether the ball rolls off form towards one particular side of the table, or if information technology moves true.

   • Echo the process on a few sections of the table. Suit the table if the ball is rolling off course towards a particular side, if necessary.
   • This method requires that you move the brawl extremely directly, which is somewhat difficult and less accurate than a level. If y'all try this, check your results against a carpenter level to be sure.

6. half-dozen

   Utilize a flat slice of glass and a marble to calculate residuum. Another style of checking for level that doesn't involve a level is to set a piece of glass in the middle of the pool table, and allow a marble roll across it.

   • Place a marble on the middle of the piece of glass. The ball should stay in place if the pool table is level. Adjust the table if the brawl rolls off of the glass towards a particular area of the table.
   • Repeat the process on every side of the tabular array. Place the glass and marble two to iii inches (5 to seven.vi cm) from every pocket on the pool table.

7. 7

   Find the lowest corner. The level should dip, or the ball should move in the same direction at both corners on the same side. If the level dips in i more than than the other, that's the corner you need to adapt.

   • If the level doesn't, turn it the other way and cheque for level on the perpendicular side.
   • When you locate the lowest corner, put the viii-ball in that pocket, and so you'll exist able to remember which i it is.

Advertisement

1. 1

   Consult your owner'due south manual, if you lot take information technology. Most puddle tables are made to exist adjustable, so you can make them level, regardless of what surface they're on. Some pool tables may have metal plates, which tin can be added or removed to heighten or lower the sides. Other pool tables take adjustable legs, with feet that can be screwed clockwise or counterclockwise, to heighten or lower that side. Your owner's transmission will provide specific data nearly your puddle table.

   • If you don't have the manual, but await at the legs to run across how they're put together, and whether or not they have adjustable components. If your pool table does not, you tin still use shims and other tiny adjustments to level the tabular array.
   • If the table features spiral-in feet or legs, they'll normally be raised by turning them to the right and lowered by turning them to the left. But always defer to the owner manual to be certain.

2. 2

   Tighten all attachment screws under the table. Sometimes, the bolts and screws used to assemble a pool table can loosen slightly over time, resulting in the table becoming off-level. If you tighten up all the attachment screws, you tin can sometimes level out the table without fifty-fifty adjusting the height.

   • Puddle tables involve any number of unlike screws and screwdrivers to tighten. Look at the screws themselves to effigy out what you lot demand, or consult the owner's transmission.

3. three

   Heighten the everyman table leg one caste. If your pool table is adjustable, raise the lowest corner of the pool table past one degree, the to the lowest degree it tin be adjusted. Leave the carpenter's level on the pool table, and check for the alter.

   • If that was too much, and the table has been unleveled in the wrong direction, lower it back to where it was and use shims to make smaller adjustments. More on this in the side by side department.

4. 4

   Adjust the other tabular array legs, if necessary. Sometimes, you'll have to make lots of footling tweaks on different sides to go the top of the tabular array completely level. It'due south partially a trial-and-error process, and so don't become discouraged. Leave the level on the meridian of the tabular array and check for level after every adjustment.

   • You lot tin too leave the over adjusted leg every bit it is, and apply shims on the over levels, if you lot'd rather. It's partially a trial-and-fault process.

5. v

   Use shims to fine-tune the level. Shims are small, tapered shards of woods that you can employ to make full gaps and adjust the height of things like pool tables. They're commonly sold in the carpentry sections of any hardware or home appurtenances store, usually in packages with variable sizes.^[iv]

   • Y'all can trim the shims to fit underneath the feet of the tabular array if necessary, to brand sure that they don't show. If the feet are big enough, though, you may not need to worry about information technology.

6. 6

   Get a few helpers if yous need to add shims. Have 1 or more assistants lift the corner of the tabular array that needs to be raised. Carefully, place a shim underneath the leg, lowering the foot onto it gently.

   • Use the carpenter's level to check the residuum of the puddle table. See how the shim has affected the level of the tiptop.
   • Keep to add shims underneath the legs until the puddle table is counterbalanced. Move to other corners if necessary, to make other adjustments.

7. 7

   Quit while you're ahead. Pool tables don't need to be admittedly flat for them to piece of work well enough to play on. If y'all can become information technology close enough, but non totally perfect, don't keep adding and removing the aforementioned shim over and over.

   • Roll a couple balls to see how true they motion. If information technology looks good to you, go with it.
   • Practise the marble-and-glass test again. If it sits still, you've got a playable tabular array.

Advertisement

Add New Question

• Question

  I got a table but it seems to take a depression spot in the heart that leveling doesn't take away. How do I get the eye up?

  

  In that location is a wooden plank that runs the width of mine to support the slate. I shimmed that lath from underneath and leveled it nicely. Hopefully you tin can exercise the aforementioned!

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

Thanks for submitting a tip for review!

Things You lot'll Need

• Pool table
• Carpenter's level
• Metal plates
• 1 or more assistants
• Shims
• Cue ball
• Flat piece of drinking glass
• Marble

Most This Article

Article Summary X

To level a puddle table, start by inspecting the legs to meet if they take adaptable components, like metallic plates or feet that can be raised and lowered. If the tabular array has spiral-in feet or legs, endeavor turning them to the right or left to raise or lower them until the table is level. If the legs aren't adaptable, try inserting wooden shims under some of the legs to level the table. As you're working, keep a level on elevation of the table then you can cheque it after each adjustment you lot brand. To learn how to effigy out what'southward causing your pool table to not be level, keep reading!

Did this summary help you?

Thank you to all authors for creating a page that has been read 237,708 times.

Did this commodity help you?

Source: https://www.wikihow.com/Level-a-Pool-Table

Share this post